Numerical simulation of aerated powder consolidation, International Journal of Non-Linear Mechanics, vol.38, issue.8, pp.1185-1194, 2003. ,
DOI : 10.1016/S0020-7462(02)00063-X
URL : http://www.dtic.mil/cgi-bin/GetTRDoc?AD=ADA388733&Location=U2&doc=GetTRDoc.pdf
Poromechanics, 2004. ,
DOI : 10.1002/0470092718
URL : https://hal.archives-ouvertes.fr/hal-00586279
Experimental Studies and Modeling of the Roller Compaction of Pharmaceutical Powders, Drexel University, vol.837, issue.1, 1860. ,
Understanding variation in roller compaction through finite element-based process modeling, Computers & Chemical Engineering, vol.34, issue.7, pp.1058-1071, 2010. ,
DOI : 10.1016/j.compchemeng.2010.04.008
Roll compaction of a pharmaceutical excipient: Experimental validation of rolling theory for granular solids, Chemical Engineering Science, vol.60, issue.14, pp.3891-3897, 2005. ,
DOI : 10.1016/j.ces.2005.02.022
Problems with processing of fine powders in roll press, Proceedings of the 24rd Biennial Conference of the Institute for Briquetting and Agglomeration, pp.199-210, 1995. ,
Comparison of various modeling methods for analysis of powder compaction in roller press, Powder Technology, vol.130, issue.1-3, pp.265-271, 2003. ,
DOI : 10.1016/S0032-5910(02)00203-6
Porous Media Fluid Transport and Pore Structure Academic press, 1992. ,
Confined particle bed comminution under compressive loads, Int. J. Miner. Process, pp.44-45, 1996. ,
DOI : 10.1016/b978-0-444-82440-0.50047-x
The effects of feed size distribution on confined-bed comminution of quartz and calcite in piston-die press, International Journal of Mineral Processing, vol.91, issue.3-4, pp.3-4, 2009. ,
DOI : 10.1016/j.minpro.2009.01.002
on the plastic flow of Coulomb solids beyond original failure, J. Appl. Mech, vol.26, pp.599-602, 1959. ,
Flow properties of bulk solids, ASTM Proceedings, vol.60, pp.1168-1181, 1960. ,
A Rolling Theory for Granular Solids, Journal of Applied Mechanics, vol.32, issue.4, 1965. ,
DOI : 10.1115/1.3627325
Modeling flow of bulk solids, Powder Technology, vol.5, issue.2, pp.93-99, 1971. ,
DOI : 10.1016/0032-5910(72)80006-8
The effect of the gaseous phase on pressures in a cylindrical silo, Powder Technology, vol.5, issue.3, pp.133-145, 1971. ,
DOI : 10.1016/0032-5910(72)80014-7
Fluid entrainment effects in roll press compaction, 1989. ,
Modeling and Control of Roller Compaction for Pharmaceutical Manufacturing. Part I: Process Dynamics and Control Framework, Journal of Pharmaceutical Innovation, vol.41, issue.2, pp.14-23, 2010. ,
DOI : 10.1179/pom.1998.41.2.131
Experimental and numerical analyses of homogeneity over strip width in roll compaction, Powder Technology, vol.206, issue.1-2, pp.154-160, 2011. ,
DOI : 10.1016/j.powtec.2010.04.030
URL : https://hal.archives-ouvertes.fr/hal-01680751
Analysis of strain stress state in roller compaction process, Powder Technology, vol.208, issue.2, pp.417-422, 2011. ,
DOI : 10.1016/j.powtec.2010.08.037
URL : https://hal.archives-ouvertes.fr/hal-01768700
Modeling the powder roll compaction process: Comparison of 2-D finite element method and the rolling theory for granular solids (Johanson's model), Powder Technology, vol.221, pp.90-100, 2012. ,
DOI : 10.1016/j.powtec.2011.12.001
Deaeration of powders in hoppers, Powder Technology, vol.27, issue.2, pp.149-162, 1980. ,
DOI : 10.1016/0032-5910(80)85017-0
Predicting the pressure distribution during roll compaction from uniaxial compaction measurements, Chemical Engineering Journal, vol.164, issue.2-3, pp.410-417, 2010. ,
DOI : 10.1016/j.cej.2009.12.022
Roller compaction/Dry granulation: Use of the thin layer model for predicting densities and forces during roller compaction, Powder Technology, vol.199, issue.2, pp.165-175, 2010. ,
DOI : 10.1016/j.powtec.2010.01.002
Flow and compression properties of feed solids for roll-type presses and extrusion presses, Powder Technology, vol.130, issue.1-3, pp.272-276, 2003. ,
DOI : 10.1016/S0032-5910(02)00204-8
influence of particle bed configurations and confinements on particle breakage, Int. J. Miner. Process, pp.44-45, 1996. ,
Experiences in dry grinding with high compression roller mills for end product quality below 20 microns, Minerals Engineering, vol.3, issue.1-2, pp.23-34, 1990. ,
DOI : 10.1016/0892-6875(90)90078-P
, Poroshk. Metall, vol.1, issue.1, p.61, 1961.